How to operate High-Speed Disperser
Setting Operations for high-speed disperser
1.Height limit switch
This switch is a safety unit, which does not allow lifting beyond the adjusted height, as long as the main drive motor is running. The height limit switch must be adjusted to stop the lift immediately as soon as the agitating element leaves the product. Make sure that there is sufficient clearance to the tank edge.
High Speed Disperser
Setting Operations for high-speed disperser
1.Height limit switch
This switch is a safety unit, which does not allow lifting beyond the adjusted height, as long as the main drive motor is running. The height limit switch must be adjusted to stop the lift immediately as soon as the agitating element leaves the product. Make sure that there is sufficient clearance to the tank edge.
high-speed disperser
high-speed disperser
a) Loosen nut
b) Shift sensor to the required height
c) Tighten nut
2.Container clamping device
The container is centered to the disperser shaft by the clamping device and force-locked to the machine. The installed safety switch prevents starting of the machine in case of insufficient tension load of the clamping device. The container clamping device must be adjusted to the container diameter.
a) Loosen lever at both sides
b) Move the container so that the disperser shaft is centered on the container. Fix the container with the clamping device.
c) Tighten the lever.
The FRANLI-Dissolver is a high-speed agitator with a toothed dispersion disk. It is suitable for dispersing, homogenizing, and mixing solids in liquids. Using the high peripheral speed at the dispersion disk, strong shearing stresses are transmitted to the product and translated into frictional work. The Dissolver is suitable for manufacturing mixing components with a viscosity of up to 200 Ns/ m2 (2 000 Poise). The protection devices being built off the high-speed disperser correspond to the instructions of the Trade Association of the Chemical Industrie.
high-speed disperser
1.Height limit switch
This switch is a safety unit, which does not allow lifting beyond the adjusted height, as long as the main drive motor is running. The height limit switch must be adjusted to stop the lift immediately as soon as the agitating element leaves the product. Make sure that there is sufficient clearance to the tank edge.
high-speed disperser
high-speed disperser
a) Loosen nut
b) Shift sensor to the required height
c) Tighten nut
2.Container clamping device
The container is centered to the disperser shaft by the clamping device and force-locked to the machine. The installed safety switch prevents starting of the machine in case of insufficient tension load of the clamping device. The container clamping device must be adjusted to the container diameter.
a) Loosen lever at both sides
b) Move the container so that the disperser shaft is centered on the container. Fix the container with the clamping device.
c) Tighten the lever.
The FRANLI-Dissolver is a high-speed agitator with a toothed dispersion disk. It is suitable for dispersing, homogenizing, and mixing solids in liquids. Using the high peripheral speed at the dispersion disk, strong shearing stresses are transmitted to the product and translated into frictional work. The Dissolver is suitable for manufacturing mixing components with a viscosity of up to 200 Ns/ m2 (2 000 Poise). The protection devices being built off the high-speed disperser correspond to the instructions of the Trade Association of the Chemical Industrie.
high-speed disperser
high-speed disperser
The following special equipment is possible:
1.Speed automatic:
The speed automatic enables an optimal operation in all viscosity ranges. It guarantees to work the machine in the normal load range and prevents at the same time an overstressing of the drive.
2.Vacuum equipment:
When manufacturing highly viscous media which do not ventilate themselves, an installation of vacuum equipment is possible for a simultaneous evacuation.
3.Scraper:
The scraper is used to strip off materials loosely sticking to the container wall. This is particularly required when treating thixotropic pastes, for which, even with large diameters of the toothed disk, no perfect circulation can be obtained.
4.Swiveling device:
With the help of the swiveling device, it is possible to use two stationary vessels, in special the design even three or four.
The machine was specially adjusted to the material as stated with the order and the specified production process. If you would like to change the product, please make sure that the machine can be used for this product as well.
Especially in hazardous locations, only such machines may be used which correspond to the regulations of the explosion protection. If you are in doubt about a possible application you have to contact FRANLI.
Copyright Notice :
This article only represents the author’s point of view.
This article is published under the authorization of the author.
Source: Franli
This article address : How to operate High-Speed Disperser
Related Products
High Speed Disperser
Architectural waterproof coating production equipment The preparation process of the high-speed disperser machine mainly includes the dispersion of pigments and fillers, grinding, coating preparation, toning, etc.
Filling Machine
Filling machines are packaging machines that load precise quantities of packaged products into various containers.
Horizontal Bead Mill
Horizontal Bead Mill is used for the grinding of a solid-liquid two-phase system. In the grinding process, the material is pumped into the Horizontal Bead Mill, and the rotating grinding disc transfers energy to the beads. The beads impact the material an
News
Laboratory Reactor: Guide to Stirring System
The laboratory reactor is composed of a pot body, a pot cover, an agitator, a jacket, a support and transmission device, a shaft seal device, etc.
Grinding Media for Bead Mill | Zirconia Beads & Zirconium Silicate Beads
Bead mills mainly use grinding balls as media, and use impact, extrusion, and friction to achieve the final grinding effect, which mainly depends on the size and hardness of the grinding beads, the filling rate of the grinding beads, and the collision frequency adjustment between the grinding beads and the particles.
Overview of Laboratory Reactor
Laboratory reactors, also known as lab reactors, are essential tools in scientific research, product development, and process optimization. These reactors provide a controlled environment for conducting chemical reactions, mixing, dispersing, and homogenizing processes.
Bead mills | Manufacturing technology in various industries
Bead mills, also known as sand mills or grinding mills, are versatile machines widely used across various industries for the wet grinding and dispersion of solid particles in liquid media.
Ribbon Blender Mixer Equipment
A ribbon blender mixer, also known as a ribbon mixer or horizontal ribbon blender, is a powerful industrial machine designed for thorough and efficient blending of various materials.
What is A Stainless Steel Reactor？
Stainless steel reactors are essential equipment in various industries, including chemical, pharmaceutical, biotechnology, and food processing.
