Faults and Trouble Shooting Methods of High Speed Disperser
Faults and Trouble Shooting Methods of High-Speed Disperser
1.Main motor doesn’t act.
1) Whether there is a power supply.
2）Check control circuit.
3) Whether thermal relay acts.
4）Check whether the frequency conversion switch is open.
5）Watch whether the potentiometer is damaged, and if it was damaged, it shall be replaced with a potentiometer of the same type.
2、If the button is damaged or its action is not sensitive, please replace it in time.
3、If the signal lamp doesn’t light, also please replace it in time. If the signal lamp is OK, please check whether the wiring is loose.
4、Dispersing shaft is driven by the transducer. If the transducer is in protection or damaged, please reference Transducer Instruction. For general protection, it can be reset by the “Stop” key on the transducer. If transducer damage is confirmed, please contact our company.
1）Whether there is a power supply.
2）Check control circuit
3）Whether thermal relay acts.
4) Watch the oil pump whether it runs clockwise.
5）Check solenoid valve if it is choked with foreign material, if there it is, please clean in time
6、Cylinder cannot descend after ascending.
1）Check solenoid valve coil whether it is burned, if it is, a new one shall be installed instantly.
2）Check control circuit.
7、Please strictly in compliance with operation procedures
This manual indicates procedures and principles for correct use and maintenance of the machine in texts and illustrations.
Please read the manual carefully before operating the machine.
Please keep the manual properly for future reference.
Working characteristics of high-speed disperser machine
High Speed Disperser
Unless under special conditions or requested by the customer, the manufacturer reserves the right to expand the scope of products and upgrade relevant manuals without upgrading previous machines and manuals. If there is any doubt, please consult the manufacturer.
Provided there is any problem with the machine, please contact the manufacturer. If any detailed information is needed, please contact the sales agent.
Casual operation or modification to the machine is not allowed for any reason.
For the following personnel hurt and property loss, the manufacturer will not bear any responsibilities:
1）Improper operation of the machine by inadequately trained staff.
2）There are conflicts between the machine and special laws in the host country.
3）Error installation.
4）Inadequate or little maintenance.
5）Using non-original manufacturer’s spare parts.
6）Operations are not in compliance with specified procedures.
Copyright Notice :
This article only represents the author’s point of view.
This article is published under the authorization of the author.
Source: Franli
This article address : Faults and Trouble Shooting Methods of High Speed Disperser
Related Products
Vacuum Kneader
The vacuum kneader is an ideal equipment that is suitable for high-viscosity material, such as high-viscosity silicone rubber, sealant, gum, cellulose, etc. Also used widely in the Paint, ink, pigment, resin, battery, cosmetic, etc industries.
Lab Three Roller Mill
Franli Lab three roll mill machine also has a safety system. Such as hopper with handguard, drip tray with integrated handguard and safety switch, removable for easy cleaning. Also safe scraper socket, Emergency-stop pushbutton. Electronic Brake.
3 Roll Mill: Manual, Hydraulic, Lab
3 Roll Mill is a great tool that is used to mix, refine, and disperse any material through three horizontal rolls situated opposite sides with different speeds.
News
Laboratory Reactor: Guide to Stirring System
The laboratory reactor is composed of a pot body, a pot cover, an agitator, a jacket, a support and transmission device, a shaft seal device, etc.
Grinding Media for Bead Mill | Zirconia Beads & Zirconium Silicate Beads
Bead mills mainly use grinding balls as media, and use impact, extrusion, and friction to achieve the final grinding effect, which mainly depends on the size and hardness of the grinding beads, the filling rate of the grinding beads, and the collision frequency adjustment between the grinding beads and the particles.
Overview of Laboratory Reactor
Laboratory reactors, also known as lab reactors, are essential tools in scientific research, product development, and process optimization. These reactors provide a controlled environment for conducting chemical reactions, mixing, dispersing, and homogenizing processes.
Bead mills | Manufacturing technology in various industries
Bead mills, also known as sand mills or grinding mills, are versatile machines widely used across various industries for the wet grinding and dispersion of solid particles in liquid media.
Ribbon Blender Mixer Equipment
A ribbon blender mixer, also known as a ribbon mixer or horizontal ribbon blender, is a powerful industrial machine designed for thorough and efficient blending of various materials.
What is A Stainless Steel Reactor？
Stainless steel reactors are essential equipment in various industries, including chemical, pharmaceutical, biotechnology, and food processing.
